Supports IEEE 802.11a/b/g/n and ac (draft) standards. Up to 450 Mbps on 2.4 GHz and up to 1300 Mbps on 5 GHz

Seamless Roaming, Fast Handover

6 internal MIMO antennas / Dual band / Three Stream

Sectorized 3D antenna design. For mounting on ceilings or desktop deployments

Band Steering shifts Dual band clients to 5 GHz for better throughput performance

The EWS360AP can operate as a stand-alone Access Point connecting to third-party PoE-capable switches but more control and versatile management of the Access Point is achievable when it is part of an EnGenius Neutron Series Wireless Network Management solution because the AP includes firmware that enables it to be immediately discovered, configured, monitored and managed from a compatible Neutron Series PoE+ Switch (EWS5912FP, EWS7928FP or EWS7952FP). This capability enables IT managers to deploy and manage up to 50 EWS360APs from a Neutron Series Switch allowing for simplified management from one browser-based interface including simultaneous firmware upgrades, clustering, traffic monitoring, bandwidth steering and many other features that can be reset or reconfigured from the convenience of the IT manager’s desktop.

Operating in both the 2.4 GHz and 5 GHz frequency spectrums and supporting 802.11a/b/g/n and ac (draft) standards the EWS360AP features wireless speeds up to 450 Mbps on the 2.4 GHz radio and up to 1300 Mbps on the 5 GHz radio, a Gigabit port for connecting to 802.3at-capable PoE Switches, and an enhanced receive sensitivity MIMO (Multiple In/Multiple Out) antenna array. As the EWS360AP is designed for deployments on ceilings where power outlets may be scarce, it also comes equipped with PoE (Power-over-Ethernet) IEEE 802.3at for use with an 802.3at-capable PoE injector or 802.3at-capable PoE Switches, drawing up to 22 watts of power. As a result, the EWS360AP is ideal for spacious environments such as large homes, small and medium-sized businesses, multiple-floor offices, hotels, hospitals, and other multi-floor buildings.

High Power, Long-Range and Multiple Floor Penetration

High transmit power on each band provides more than twice the wireless coverage over mainstream competitors and enables the wireless signal for faster connectivity to client devices and enables the wireless signal to penetrate floors, ceilings, and walls. Internal MIMO antenna array provides better reception and performance as clients change their orientation.

Seamless Roaming, Fast Handover

Keeps client devices connected as they roam within the network.

Wireless Traffic Shaping

Gives IT managers the ability to restrict bandwidth on each frequency as necessary.

SSID-to-VLAN Tagging

Can be configured to broadcast up to 16 SSIDs (8 SSIDs per frequency band). Each SSID can be tagged to a specified network VLAN for different user access tiers based on established access rights.

1- User capacity performance results may vary based on topology configuration, structural and architectural elements, environmental factors, type of data traffic, RF capabilities of client devices, distance, RF interference in the operating environment and other factors.

Technical Specifications

Hardware
RF: 2.4 and 5 GHz Frequency Bands
Standard: IEEE 802.11a/b/g/n/ac
Radio I: 11b/g/n: 2.412~2.484 GHz
Radio II: 11a/n: 5.18-5.24 and 5.26-5.32 and 5.5-5.7 and 5.745-5.825 GHz
Data Rate: Up to 450 Mbps in the 2.4 GHz frequency band; Up to 1300 Mbps in the 5GHz band
Memory: 128MB
Flash Memory: 16MB
Power Consumption: Up to 22W

Antenna
3 x 3 dBi 2.4 GHz internal antennas
3 x 5 dBi 5 GHz internal antennas

Physical Interface
1 x RJ-45 Gigabit Ethernet (10/100/1000 Mbps) - PoE capable
1 x Reset Button
1 x Power Connector

Power Requirements
Power Supply: 100 to 240 VDC ± 10%, 50/60 Hz
(depends on different countries)
Active Ethernet (Power-over-Ethernet, IEEE 802.3at)
Power Adapter (United States) 48VDC/0.375A
Device: 12V/2A

Modulations
OFDM: BPSK, QPSK, 26-OAM, 64-QAM, DBPSK, DQPSK, CCK

Operating Channels
2.4 GHz: US/Canada 1-11
5 GHz: Country dependent for the following ranges:
36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165

Management

Operation Modes
Access Point, Mesh AP (available soon)

Multiple BSSID
Supports up to 8 BSSIDs per radio

LAN
IP (check validity and DHCP server IP range) MAC

SSID-to-VLAN Tagging
Supports 802.1q SSID-to-VLAN tagging

Spanning Tree
Supports 802.1d Spanning Tree Protocol

Wireless
Wireless Mode: 11a/11b/11g/11n/11ac (draft)
Channel selection (settings vary by country)
Channel bandwidth (Auto, 20 MHz, 40 MHz)

Transmission Rate
2.4 GHz: 11n only, 11b/b/n mix, 11b only, 11b/g, 11g only
5 GHz: 11n only, 11a/n mix, 11a only

QoS
WMM (Wireless Multimedia)

Wireless Management Features (with Neutron Series Switch)
Access Point Auto Discovery and Provisioning
Access Point Auto IP Assignment
Access Point Cluster Management
Remote Access Point Rebooting
Access Point Device Name Editing
Access Point Radio Settings
Band Steering
Traffic Shaping
Fast Handover
Fast Roaming
Access Point Client Limiting
Mesh Network*
Wireless Security (WEP, WPA/WPA2 Enterprise, WPA/WPA2 PSK)
VLANs for Access Point- Multiple SSIDs
Guest Network
Access Point Status Monitoring
Wireless Client Monitoring
Wireless Traffic & Usage Statistics
Real-time Throughput Monitoring
Visual Topology View
Floor Plan View
Map View
Secure Control Messaging
SSL Certificate
Local MAC Address Database
Remote MAC Address Database (RADIUS)
Unified Configuration Import / Export
Bulk Firmware Upgrade Capability
Intelligent Diagnostics

* Mesh networking mode available soon as a free firmware upgrade

Management (cont.)

Tx Power Control
Adjust transmit power by dBm

Configuration
Web-based configuration (http)

Firmware Upgrade
Via web browser, settings are reserved after upgrade

Administrator Setting
Administrator Username and Password Change

Reset Setting
Reboot (press and hold for 2 seconds).
Reset to factory default (press and hold for 10 seconds)

System Monitoring
Status Statistic and Event Log

SNMP
V1, V2c, V3

MIB
MIB I, MIB II (RFC1213) and private MIB

Traffic Shaping
Incoming and outgoing wireless traffic shaping

Auto-channel Selection
Automatically selecting least congested channel

Bandwidth Measurement
IP range and bandwidth management

Auto Reboot
Reboot Access Point by minute, hour, day, or week

Backup and Restore
Save and restore settings through Web interface

CLI
Supports Command Line Interface

Diagnosis
IP pinging statistics

Log
SysLog and Local Log support

LED Control
On/Off

AP Detection
Scanning for available EnGenius APs

Wireless Security
WPA/WPA2 Personal (WPA-PSK using TKIP or AES)
WPA/WPA2 Enterprise (WPA-EAP using TKIP)
802.1X RADIUS Authenticator: MD5/TLS/TTLS, PEAP
SSID broadcast enable/disable
MAC Address Filtering, Up to 50 fields
L2 Isolation (Access Point mode)

QoS (Quality of Service)
WMM (Wireless Multimedia)
Environmental & Physical

Temperature Range
Operating: 0 to 50ºC (32º to 122ºF)
Storage temperature: -20ºC to 60ºC (-4Fº to 140ºF)

Humidity (non-condensing)
Operating: 90% or less
Storage: 90% or less

Certifications
FCC, IC

Maximum data rates are based on IEEE 802.11 standards. Actual throughput and range may vary depending on many factors including environmental conditions, distance between devices, radio interference in the operating environment, and mix of devices in the network. Features and specifications subject to change without notice. Trademarks and registered trademarks are the property of their respective owners. For United States of America: Copyright ©2014 EnGenius Technologies, Inc. All rights reserved.
Dimensions & Weights

EWS360AP Device
Weight: 0.80 lbs.
Length: 6.5”
Width: 6.5”
Height: 1.64”

Package Contents
EWS360AP Dual Band AC1750 Indoor Access Point
12V/2A Power Adapter
T-Rail Mounting Kit
Ceiling Mount and Wall Screw Kit
Mounting Bracket
RJ-45 Ethernet Cable
Quick Installation Guide

روتر ان جنیوس EWS360AP 2.4 GHz Indoor

محصولات مشابه

روتر ان جنیوس EWS357AP